Making a Foredom flexible shaft rotary tool stand – rifleshooter.com

Making a Foredom flexible shaft rotary tool stand – rifleshooter.com



Like most gunsmiths, we use the Foredom flexible shaft rotary tool for many tasks around the shop. While rotary tools can get you into trouble if you aren’t careful, the ability to grind and polish small areas in difficult to reach areas, allows these small flexible shaft tools to perform some tasks you can’t do by hand.

Once you get a Foredom tool, locating seems to be a problem. Equipped with a hanger, our initial installation was a large hook bolted to the wall. The downside of this was the work had to be fairly close to the where the motor was mounted and work flow was effected. Looking around, we found a number of more complex (and expensive) hanger systems were available. Looking at the pile of 1″ black pipe I had in the corner of the shop, I decided fabricating a stand would be the way to go.

In this post we’ll take a look at how I made the hanger for my Foredom.

The tool I am making the hanger for came from Brownells. It is a model SR-8D set, as we use it often!

I decided to make the hanger system from 1″ black pipe and fittings. This was largely due to the fact that I had a bunch of extra pipe and fittings on hand. Rather than cut and thread the pipe, which is fairly labor intensive, I decided for any shorter pieces, I’d bore the pipe fittings on the lathe and simply slip it over the pipe and weld it in place. if you own a machine shop this is far easier than cutting 1″ NPT male threads. If your buddy had a pipe threading machine, that may be the way to go.

I bored my fittings on one pass on my Precision Matthews PM-1440GT lathe with a large boring bar. A part like this “T” was bored in two passes, one from each end.

I cut a number of fittings to allow them to pass over. Here is a flange and two T’s. The flange will secure the vertical pipe to the workbench, while the “T” fittings will be used to hold the motor and the tools.

I fabricated two arms that would act as tool holders. These are short sections of 1″ pipe approximately 18″ long. I welded one end to a “T” and the other to a cap. If you know how to weld, you’ll notice I’m more of a grinder than a welder!

Each of the arms holds a number of 1/8 shank tools. I drilled 3 rows of holes spaces 1/2″ apart along the top of each.

To weld the fittings on square to the pipe, I used a straight piece of angle as a square.

To mount to motor to stand, I bored a straight coupling and welded a cut off eye loop too it.

I then attached the motor hanging bracket to a 24″ long pipe of pipe that was welded to a “T” fitting. To hold the motor at the correct height, I bored a 1″ coupling and slid it on the vertical section of pipe. I then welded this in place.

The vertical section of pipe in the stand is about 8 feet long. It needs a stable base to hold it. I decided to bolt the bottom to the concrete and pass it through our workbench top. I used a self-feeding drill bit to drill through the counter top.

I then bolted the flange to the top.

I checked the upright for plumb and anchored the flange at the bottom of the vertical upright to the floor. This is a rock solid method of attaching the stand to the bench.

Here is a view of the finished stand. Note the two arms that hold the various 1/8′ tool bits.

In addition to the tool being able to swing 360 degrees around the vertical upright, the motor can slide along the arm.

Another view of the tool storage.

To top off the stand, I machine an aluminum plug to hold a Luxo magnifying lamp. These lamps are available at Brownells and indispensable in the gun shop.

A look at the finished stand. In its current location the Foredom can reach three different work stations equipped with vices using the same tool. Plus, the bits are all available and if we need more light, we simply swing it into place.





Source link

Join the Discussion

Your email address will not be published. Required fields are marked *

arrow